// Lesson 3 of 49 · Network fundamentals
Cabling and the physical layer
Layer 1 problems — a bad cable, a wrong transceiver, a dirty fibre — cause a large share of real-world outages. Knowing your media saves hours.
Copper: twisted pair (UTP)
Ethernet copper cables contain 8 wires in 4 twisted pairs ending in RJ-45 connectors. Twisting reduces interference.
| Category | Typical use |
|---|---|
| Cat 5e | 1 Gbps up to 100 m |
| Cat 6 | 1 Gbps up to 100 m; 10 Gbps over shorter runs |
| Cat 6A | 10 Gbps up to 100 m |
The maximum length of a copper Ethernet channel is 100 m. Longer runs need a switch in between or fibre.
Which pins are used
- 10BASE-T and 100BASE-TX use only two pairs: pins 1–2 and 3–6. A PC transmits on 1–2 and receives on 3–6; a switch does the opposite.
- 1000BASE-T and faster use all four pairs in both directions at once.
Straight-through vs crossover
- Straight-through: pin 1 to pin 1, and so on. Traditionally used between unlike devices (PC to switch, router to switch).
- Crossover: transmit pairs swapped. Traditionally used between like devices (switch to switch, PC to PC).
Today almost every port supports auto-MDIX, which detects the cable type and swaps pairs internally, so either cable works. You still need to know the difference for older equipment and for exam-style questions.
Fibre
Fibre carries light instead of electricity: no electrical interference, much longer distances, and higher speeds.
| Multimode (MMF) | Single-mode (SMF) | |
|---|---|---|
| Core | Larger (50 or 62.5 µm) | Very small (about 9 µm) |
| Light source | LED / VCSEL | Laser |
| Distance | Hundreds of metres | Kilometres to tens of kilometres |
| Typical use | Inside buildings and data centres | Between buildings, campuses, WAN |
Switches accept fibre through pluggable transceivers (SFP, SFP+, QSFP). The transceiver type, the fibre type and the connector (LC is the most common) must all match on both ends.
Power over Ethernet (PoE)
PoE delivers power and data over the same copper cable, so phones, APs and cameras need no separate power supply. The switch negotiates how much power each device needs. When planning, check the switch's total PoE budget — a switch can run out of power before it runs out of ports.
Interface speed and duplex
- Full duplex: send and receive at the same time — the normal mode on switched links.
- Half duplex: one direction at a time (legacy hubs, shared media).
Both ends should autonegotiate. A duplex mismatch (one side full, one side half) causes slow, erratic performance and growing error counters — late collisions on the half-duplex side, CRC/runts on the full-duplex side.
SW1# show interfaces GigabitEthernet1/0/5
GigabitEthernet1/0/5 is up, line protocol is up (connected)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
Key points
- Copper Ethernet: 4 pairs, RJ-45, 100 m maximum.
- 10/100 Mbps use pins 1-2 and 3-6; Gigabit uses all four pairs.
- Auto-MDIX makes straight-through vs crossover mostly irrelevant on modern gear.
- Multimode = shorter, single-mode = longer; transceivers and connectors must match.
- Duplex mismatch shows up as errors and poor performance, not a down link.
Sign in to save your lesson progress across devices. You can read every published lesson without an account.