Skip to content
FALCON CORETECHNOLOGIES

// Lesson 42 of 49 · Security fundamentals

Port security, DHCP snooping and Dynamic ARP Inspection

Limiting MAC addresses per port, blocking rogue DHCP servers, and stopping ARP spoofing on access switches.
2 min read#port-security#dhcp-snooping#dai

The access layer is where untrusted devices plug in. Three switch features stop the most common Layer 2 attacks.

Port security

Limits which and how many MAC addresses may use a port — defeating MAC flooding and casual device swaps.

SW1(config)# interface GigabitEthernet1/0/5
SW1(config-if)# switchport mode access
SW1(config-if)# switchport port-security
SW1(config-if)# switchport port-security maximum 2
SW1(config-if)# switchport port-security mac-address sticky
SW1(config-if)# switchport port-security violation restrict
  • Port security works only on access (or trunk) ports that are statically set — not on dynamic DTP ports.
  • Sticky learns the connected MACs and writes them into the running config.
Violation mode Drops offending traffic Logs / counts Disables the port
shutdown (default) Yes Yes Yes — err-disabled
restrict Yes Yes No
protect Yes No No
SW1# show port-security interface GigabitEthernet1/0/5
SW1# show port-security address
SW1# show interfaces status err-disabled

Recover a shut-down port with shutdown then no shutdown, or automatically:

SW1(config)# errdisable recovery cause psecure-violation
SW1(config)# errdisable recovery interval 300

DHCP snooping

Classifies ports as trusted (towards the real DHCP server) or untrusted (everything else). DHCP server messages (Offer, Ack) arriving on untrusted ports are dropped, so a rogue DHCP server cannot hand out a malicious gateway.

SW1(config)# ip dhcp snooping
SW1(config)# ip dhcp snooping vlan 10,20
SW1(config)# no ip dhcp snooping information option     ! often needed when the server is a router/relay that rejects option 82
SW1(config)# interface GigabitEthernet1/0/24
SW1(config-if)# ip dhcp snooping trust                   ! uplink towards the DHCP server
SW1(config)# interface range GigabitEthernet1/0/1 - 20
SW1(config-if-range)# ip dhcp snooping limit rate 10     ! DHCP packets per second

Snooping also builds a binding table (MAC, IP, VLAN, port, lease):

SW1# show ip dhcp snooping
SW1# show ip dhcp snooping binding

Dynamic ARP Inspection (DAI)

Checks ARP packets on untrusted ports against the DHCP snooping binding table. An ARP claiming an IP/MAC pair that DHCP never handed to that port is dropped — stopping ARP spoofing and man-in-the-middle attacks.

SW1(config)# ip arp inspection vlan 10,20
SW1(config)# interface GigabitEthernet1/0/24
SW1(config-if)# ip arp inspection trust
SW1# show ip arp inspection

Devices with static IP addresses have no binding, so DAI would drop their ARPs — add them with an ARP ACL or static bindings first.

Order of deployment

  1. Port security on access ports.
  2. DHCP snooping (trust uplinks, verify the binding table fills).
  3. DAI on the same VLANs (handle static hosts first).

Key points

  • Port security: maximum MACs, sticky learning, violation shutdown/restrict/protect.
  • DHCP snooping: trust only ports towards real DHCP servers; it builds the binding table.
  • DAI uses that binding table to drop forged ARP replies.
  • err-disabled ports need manual or automatic recovery.

Sign in to save your lesson progress across devices. You can read every published lesson without an account.