Skip to content
FALCON CORETECHNOLOGIES

// Lesson 31 of 49 · IP routing

Configuring single-area OSPFv2

Enabling OSPF with network statements or per interface, passive interfaces, default route origination, tuning and verification.
3 min read#ospf#configuration

Minimal configuration

R1(config)# router ospf 1
R1(config-router)# router-id 1.1.1.1
R1(config-router)# network 10.1.12.0 0.0.0.3 area 0
R1(config-router)# network 192.168.10.0 0.0.0.255 area 0
R1(config-router)# passive-interface GigabitEthernet0/0
  • router ospf 1 — the process ID is local; it does not need to match between routers.
  • network <address> <wildcard> area <id> — any interface whose IP falls inside the range joins OSPF in that area. The network statement does not decide what is advertised by itself; it enables OSPF on matching interfaces, and their subnets are then advertised.
  • The wildcard is the inverted mask: /30 → 0.0.0.3, /24 → 0.0.0.255. You can also match a single interface exactly: network 10.1.12.1 0.0.0.0 area 0.

Per-interface method (clearer)

R1(config)# interface GigabitEthernet0/1
R1(config-if)# ip ospf 1 area 0

Passive interfaces

A passive interface is advertised into OSPF but sends no Hellos — so no neighbour can form there. Use it on every LAN where there are no other routers (user VLANs, loopbacks):

R1(config-router)# passive-interface default
R1(config-router)# no passive-interface GigabitEthernet0/1

Advertising a default route

The edge router with the internet connection shares its default route with the rest of the area:

R1(config)# ip route 0.0.0.0 0.0.0.0 203.0.113.1
R1(config)# router ospf 1
R1(config-router)# default-information originate

Other routers then show O*E2 0.0.0.0/0.

Tuning

R1(config-router)# auto-cost reference-bandwidth 100000       ! same on all routers
R1(config)# interface GigabitEthernet0/1
R1(config-if)# ip ospf cost 10                                  ! override cost on one link
R1(config-if)# ip ospf priority 0                               ! never become DR here
R1(config-if)# ip ospf network point-to-point                   ! no DR/BDR on a 2-router link
R1(config-if)# ip ospf hello-interval 5                         ! must match the neighbour

Verify — in this order

R1# show ip ospf neighbor
Neighbor ID     Pri   State           Dead Time   Address         Interface
2.2.2.2           1   FULL/DR         00:00:36    10.1.12.2       GigabitEthernet0/1

R1# show ip ospf interface brief
Interface    PID   Area   IP Address/Mask    Cost  State Nbrs F/C
Gi0/1        1     0      10.1.12.1/30       1     BDR   1/1
Gi0/0        1     0      192.168.10.1/24    1     DR    0/0

R1# show ip route ospf
R1# show ip protocols
R1# show ip ospf database

When a neighbour does not come up

Symptom Check
No neighbour at all Interface passive? Interface in OSPF (show ip ospf interface brief)? Same subnet? ACL blocking 224.0.0.5?
Stuck in INIT Hellos only arrive one way — ACL, VLAN or one-way link
Stuck in EXSTART/EXCHANGE MTU mismatch
Neighbour flaps Hello/dead timer mismatch, unstable link
Neighbour up but routes missing Network not enabled in OSPF, wrong area, route filtered

show ip ospf interface shows the timers, area, cost, network type and DR/BDR for each interface — compare the two sides.

OSPFv3 (IPv6) quick look

R1(config)# ipv6 unicast-routing
R1(config)# ipv6 router ospf 1
R1(config-rtr)# router-id 1.1.1.1
R1(config)# interface GigabitEthernet0/1
R1(config-if)# ipv6 ospf 1 area 0

Key points

  • Process ID is local; area and subnet must match.
  • network statements enable OSPF on matching interfaces (wildcard masks).
  • Make LAN interfaces passive; use default-information originate at the edge.
  • Troubleshoot with show ip ospf neighbor, then show ip ospf interface.

Sign in to save your lesson progress across devices. You can read every published lesson without an account.